Construction Adhesives

Knauf Cornice Adhesive is a plaster-based setting compound for bonding paper-faced and plaster cornices to plasterboard and masonry, and for reinforcing cornice joints. The Compounds and Adhesives Catalogue lists the DIY 3 kg pail as Cornice Adhesive 45 in a smaller pack.

This listing is for one 3 kg DIY pail (Knauf material 00747816 / SKU 747816). The 3 kg DIY size is in the catalogue; the live Cornice Adhesive variants table currently shows 10 kg and 20 kg bags.

Features

• Same Cornice Adhesive 45 chemistry in a DIY pail
• Mixes easily; excellent wet tack and adhesion
• Approximately 45-minute set
• Also suitable for small decorative plaster fixings and joint reinforcing

This Pack

Applications

• DIY cornice installation and joint reinforcing
• Small decorative plaster fixings

Documents

• Cornice Adhesive 45, 60 and 90 Product Datasheet
• Cornice Adhesive Safety Data Sheet
• VOC Content Test Certificate – Cornice Adhesive
• Compounds and Adhesives Selector Chart
• Compounds and Adhesives Catalogue

Selleys Liquid Nails Mirror & Metal is a neutral-cure silicone adhesive formulated to bond mirrors safely without attacking the silver backing. This 310g pack is the non-corrosive choice for mirror and metal installation.

Key Features

• Neutral-cure silicone — will not de-silver mirror backing
• High-strength, durable bond
• Moisture and heat resistant
• Suitable for interior and exterior use
• Easy to apply
• Bonds a wide temperature range once cured

Ideal for: Installing mirrors and bonding metal, glass, tiles and ceramics. Not for aquariums or below-waterline use. Note: this silicone-based adhesive is not paintable.

Premium Bond™ Stud Adhesive is a water-based synthetic adhesive for bonding plasterboard to timber and metal studs on walls and ceilings. The buttery, no-slump consistency gives fast grab and good adhesive transfer.

This listing is for one 5.2 kg trade pail (Knauf material 00820819 / SKU 820819), as listed in the Compounds and Adhesives Catalogue.

Features

• Easy to use with rapid tack and a tough bond
• No-slump butter consistency
• Suitable for timber and metal studs
• Air-drying — minimum 24 hours (typically 24–48 hours)
• Green Star VOC 40 g/L (limit 50 g/L)

This Pack

Applications

• Bonding plasterboard to timber or metal wall and ceiling studs
• Use with mechanical fasteners as required by the Knauf installation manual

Documents

• Premium Bond Stud Adhesive Product Datasheet
• Premium Bond Stud Adhesive Safety Datasheet
• VOC Content Test Certificate – Premium Bond Stud Adhesive
• Compounds and Adhesives Selector Chart
• Compounds and Adhesives Catalogue

Premium Bond™ Stud Adhesive is a water-based synthetic adhesive for bonding plasterboard to timber and metal studs on walls and ceilings. The buttery, no-slump consistency gives fast grab and good adhesive transfer.

This listing is for one 1.3 kg DIY pail (Knauf material 00820817 / SKU 820817), as listed in the Compounds and Adhesives Catalogue.

Features

• Easy to use with rapid tack and a tough bond
• No-slump butter consistency
• Suitable for timber and metal studs
• Air-drying — minimum 24 hours (typically 24–48 hours)
• Green Star VOC 40 g/L (limit 50 g/L)

This Pack

Applications

• Bonding plasterboard to timber or metal wall and ceiling studs
• Use with mechanical fasteners as required by the Knauf installation manual

Documents

• Premium Bond Stud Adhesive Product Datasheet
• Premium Bond Stud Adhesive Safety Datasheet
• VOC Content Test Certificate – Premium Bond Stud Adhesive
• Compounds and Adhesives Selector Chart
• Compounds and Adhesives Catalogue

Knauf Cornice Adhesive is a plaster-based setting compound for bonding paper-faced and plaster cornices to plasterboard (and masonry), and for reinforcing cornice joints. It can also fix other plaster decorative products, back-block joints and laminate plasterboard sheets.

This listing is for one 20 kg bag of Cornice Adhesive 45 (Knauf material 00747812 / SKU 747812), as listed on the Cornice Adhesive product page.

Features

• Mixes easily to a creamy, lump-free gauge
• Excellent wet tack, adhesion and water retention
• 45-minute set (also available as 60 and 90 minute grades)
• Yellow pigmentation for easy identification
• VOC less than 8 g/L

This Pack

Applications

• Bonding SHEETROCK® Cove and other paper-faced or plaster cornices
• Reinforcing cornice joints; back-blocking and laminating plasterboard
• Use temporary nails or screws on long or heavy lengths until the adhesive has set

Documents

• Cornice Adhesive 45, 60 and 90 Product Datasheet
• Cornice Adhesive Safety Data Sheet
• VOC Content Test Certificate – Cornice Adhesive
• Compounds and Adhesives Selector Chart
• Compounds and Adhesives Catalogue

Safe-T-Bond is formulated with strong initial suction/grab, making it ideal for installing wall panelling, flooring, skirting boards and architraves, and for bonding particle-board sub-floor to timber, steel and concrete joists.

• Low odour – no solvent fumes
• Easy-to-use, re-sealable sausage pack – no caulking gun needed
• Easy clean-up with water
• Fast initial grab minimises slippage on vertical surfaces
• Bridges gaps up to 9mm, effective on uneven surfaces
• Long repositioning time – up to 60 minutes

Specifications

• Pack size: 1 litre
• Colour: pale yellow
• Chemical type: polyurethane
• Open time: 20 min @ 25°C
• Cure time: 24 hours @ 25°C
• Service temperature: -5°C to 80°C
• Bond strength exceeds AS2329-1999

Description

CRC ADOS Multi-Purpose Spray Adhesive is a glue that bonds most materials quickly and easily, giving a long-lasting bond. It is formulated to give a fast tack-off, low-soak spray and dries clear. It is a pressure-sensitive one-way adhesive that remains repositionable for 1-2 minutes, eliminating costly errors with expensive materials. Once positioned, the adhesive will bond within 10-20 minutes. Full cure will take 24 hours. Caution: Do not use where heat-resistant or immersed in water bonds are required. Always test areas in a typical bonding situation before applying to the entire area.

Applications

• CRC ADOS Multi-Purpose Spray Adhesive
• is suitable for bonding paper, leather, carpet, PVC foam, polystyrene, cardboard, cloth, fabrics, foils, cork, some rubbers, felt, labelling, sailcloths, mounting photographs and fibreglass. Suitable for use on wood and metal when bonding dissimilar materials.

More Information

CRC ADOS Multi-Purpose Spray Adhesive bonds most materials quickly and easily, giving a long-lasting bond. CRC ADOS Multi-Purpose Spray Adhesive is formulated to dry clear and gives a fast tack, low soak spray. CRC ADOS Multi-Purpose Spray Adhesive remains repositionable for 1-2 minutes, eliminating costly errors with expensive materials. Once finally positioned, CRC ADOS Multi-Purpose Spray Adhesive will bond within 10-20 minutes. Full cure will take 24 hours. How to use CRC ADOS Multi-Purpose Spray Adhesive Directions: Ensure the surface is clean and dry before use Shake the can well. Spray 20-25cm from the surface using a smooth, sweeping action. Use only a light coat. Avoid spraying it near eyes or open flames When finished spraying, clean the valve by turning the can upside down and pressing the button until only pressure escapes Using on non-porous surfaces Apply to one surface and allow to tack off for 1 minute (maximum 4 minutes) Press together firmly Use a roller for fine finishes Using on porous surfaces Apply to both surfaces and allow to tack off for 1 minute (maximum 4 minutes) Press together firmly Some porous surfaces may require pre-coating to seal material. Allow a thin coat to dry thoroughly before applying a final coat of adhesive

Specifications

Resources

• Safety Data Sheet
• Technical Data Sheet

Description

CRC ADOS Multi-Purpose Spray Adhesive is a glue that bonds most materials quickly and easily, giving a long-lasting bond. It is formulated to give a fast tack-off, low-soak spray and dries clear. It is a pressure-sensitive one-way adhesive that remains repositionable for 1-2 minutes, eliminating costly errors with expensive materials. Once positioned, the adhesive will bond within 10-20 minutes. Full cure will take 24 hours. Caution: Do not use where heat-resistant or immersed in water bonds are required. Always test areas in a typical bonding situation before applying to the entire area.

Applications

• CRC ADOS Multi-Purpose Spray Adhesive
• is suitable for bonding paper, leather, carpet, PVC foam, polystyrene, cardboard, cloth, fabrics, foils, cork, some rubbers, felt, labelling, sailcloths, mounting photographs and fibreglass. Suitable for use on wood and metal when bonding dissimilar materials.

More Information

CRC ADOS Multi-Purpose Spray Adhesive bonds most materials quickly and easily, giving a long-lasting bond. CRC ADOS Multi-Purpose Spray Adhesive is formulated to dry clear and gives a fast tack, low soak spray. CRC ADOS Multi-Purpose Spray Adhesive remains repositionable for 1-2 minutes, eliminating costly errors with expensive materials. Once finally positioned, CRC ADOS Multi-Purpose Spray Adhesive will bond within 10-20 minutes. Full cure will take 24 hours. How to use CRC ADOS Multi-Purpose Spray Adhesive Directions: Ensure the surface is clean and dry before use Shake the can well. Spray 20-25cm from the surface using a smooth, sweeping action. Use only a light coat. Avoid spraying it near eyes or open flames When finished spraying, clean the valve by turning the can upside down and pressing the button until only pressure escapes Using on non-porous surfaces Apply to one surface and allow to tack off for 1 minute (maximum 4 minutes) Press together firmly Use a roller for fine finishes Using on porous surfaces Apply to both surfaces and allow to tack off for 1 minute (maximum 4 minutes) Press together firmly Some porous surfaces may require pre-coating to seal material. Allow a thin coat to dry thoroughly before applying a final coat of adhesive

Specifications

Resources

• Safety Data Sheet
• Technical Data Sheet

Description

CRC ADOS Ultra High Strength Spray Adhesive is a contact adhesive that gives an immediate and permanent bond on a wide variety of surfaces. It is formulated to give low soak, cure fast, dry clear, and be non-staining. It has high heat resistance and is suitable on porous and non-porous surfaces, making it ideal for a wide variety of applications, where permanent, high-strength bonds are essential. CRC ADOS Ultra High Strength Spray Adhesive uses a unique resin system, making it resistant to breakdown from plasticiser migration. Caution: Do not use for bonds that are immersed in water. Always test areas in a typical bonding situation before applying to the entire area.

Applications

• CRC ADOS Ultra High Strength Spray Adhesive
• is suitable for bonding porous and non-porous surfaces, wood, metal, concrete, flooring (cork tiles, carpet, linoleum, hardwood, laminate), some plastics, laminates, particle board and foam. It is not suitable for use on polystyrene.

More Information

CRC ADOS Ultra High Strength Spray Adhesive is a convenient, easy way to achieve strong, permanent bonds on a wide variety of surfaces. The performance of the contact adhesive is not affected by high temperatures, making it suitable for a number of applications. It has a low soak, cures fast, dries clear, and will not stain. CRC ADOS Ultra High Strength Spray Adhesive is not suitable for one-surface bonding and should be used as a two-surface contact adhesive. CRC ADOS Ultra High Strength Spray Adhesive is suitable for porous and non-porous surfaces. Fitted with a variable nozzle, it allows accurate spraying while reducing product wastage. Bonds are created within one minute. Full cure will take 24 hours. How to use CRC ADOS Ultra High Strength Spray Adhesive Directions: Ensure the surface is clean and dry Shake the can well Adjust the nozzle for the width of spray required. Low, medium, or high For best results, use when the temperature of the aerosol can and surfaces are a minimum of 8°C Some porous surfaces may require pre-coating to seal material. Allow a thin coat to dry thoroughly before applying a final coat of adhesive For an extra strong bond, coat surfaces twice. Allow 5 minutes between coats Spray 20-25cm from surfaces using a smooth sweeping action Apply to both surfaces and allow to tack off for 5-10 minutes Press together firmly so that all surfaces are touching When finished spraying, clean the valve by turning the can upside down and pressing the button until only pressure escapes

Specifications

Resources

• Safety Data Sheet
• Technical Data Sheet

Selleys Liquid Nails is the original high-strength construction adhesive — a solvent-based, all-weather bonder for tough interior and exterior building jobs. This 100g pack delivers a proven, long-lasting hold across the widest range of building materials.

Key Features

• Solvent-based, high-strength construction adhesive
• Excellent water resistance
• Suitable for interior and exterior use
• Meets Australian Standard AS 2329-1999
• Paintable once fully cured
• Made in Australia

Ideal for: Bonding timber, panelling, skirting and architraves, plus timber to concrete, tiles, MDF and ceramic. Not for polyethylene, polypropylene, mirrors or permanent water immersion.

Selleys Liquid Nails Heavy Duty is an extra-strong construction adhesive for the toughest jobs, rated twice as strong as Liquid Nails Original in less than half the time. This 350g gap-filling formula grips heavy materials with no slump, even overhead.

Key Features

• Twice as strong as Liquid Nails Original, and faster
• No slump or stringing, even on overhead and vertical beads
• Gap-filling formula suits most building materials
• Excellent water and weather resistance for interior and exterior use
• Easy to apply, even at low winter temperatures
• Paintable once cured

Ideal for: Heavy or bulky materials — panelling, stone tiles, timber and furniture — and vertical or overhead installations. Mechanical fasteners can be removed after 8 hours.

Selleys Liquid Nails Exterior is a water-based construction adhesive purpose-built for outdoor use, holding its strength in extreme weather. This 350g pack bonds both wet and dry timber for reliable all-weather results.

Key Features

• Water-based adhesive for all-weather exterior bonding
• Bonds both wet and dry timber
• No sag or stringing
• Paintable once cured
• Excellent water resistance; meets AS 2329-1999
• Made in Australia

Ideal for: Decking, cladding and fencing — bonds timber, plasterboard, MDF, concrete, tiles, masonry, glass and Colorbond®. Not for roofing or permanent water immersion.

Selleys Liquid Nails Extreme Grab is an instant-grab, moisture-cure construction adhesive that holds immediately — no clamps or bracing needed for most jobs. This 290ml pack sets in around 10 seconds for fast vertical bonding and repairs.

Key Features

• Extreme instant grab — sets in around 10 seconds
• No clamps or bracing needed for most jobs
• Excellent for vertical work
• Strong, durable long-term bond
• Good water resistance for interior and exterior use
• Ideal for rapid repairs

Ideal for: Bonding timber, plasterboard, MDF, metal, ceramic and acoustic panels. Not for polyethylene or polypropylene.

Selleys Liquid Nails Landscape is a construction adhesive designed for outdoor and landscaping projects, with strong initial grab and weatherproof durability. This 415g pack withstands rain, heat and UV for lasting outdoor bonds.

Key Features

• Formulated for landscaping and outdoor use
• Strong initial grab and long-term bond
• Water-resistant and weatherproof (rain, heat and UV)
• Paintable once cured
• Meets Australian Standard AS 2329-1999
• Bonds rocks, stone and masonry

Ideal for: Decking, cladding, fencing and bonding rocks, stones and retaining/landscape materials — timber, masonry, stone, concrete and tiles.

Selleys Liquid Nails Fast is a water-based, high-strength construction adhesive with strong instant grab that holds vertical jobs immediately and reduces the need for clamping. This 130g pack is low odour with easy water clean-up.

Key Features

• Water-based, low odour with easy water clean-up
• High instant grab — ideal for vertical jobs
• Reduces or eliminates the need for clamping
• Paintable once cured
• Good water resistance for interior and exterior use
• Made in Australia

Ideal for: Bonding timber, plasterboard, MDF, concrete, tiles and acoustic panels. Not for mirrors, prolonged moisture, polyethylene or polypropylene.

Selleys Liquid Nails Fast is a water-based, high-strength construction adhesive with strong instant grab that holds vertical jobs immediately and reduces the need for clamping. This 420g pack is low odour with easy water clean-up. Supplied as a trade 20-pack of the 420g cartridge.

Key Features

• Water-based, low odour with easy water clean-up
• High instant grab — ideal for vertical jobs
• Reduces or eliminates the need for clamping
• Paintable once cured
• Good water resistance for interior and exterior use
• Made in Australia

Ideal for: Bonding timber, plasterboard, MDF, concrete, tiles and acoustic panels. Not for mirrors, prolonged moisture, polyethylene or polypropylene.

Selleys Liquid Nails is the original high-strength construction adhesive — a solvent-based, all-weather bonder for tough interior and exterior building jobs. This 680g pack delivers a proven, long-lasting hold across the widest range of building materials.

Key Features

• Solvent-based, high-strength construction adhesive
• Excellent water resistance
• Suitable for interior and exterior use
• Meets Australian Standard AS 2329-1999
• Paintable once fully cured
• Made in Australia

Ideal for: Bonding timber, panelling, skirting and architraves, plus timber to concrete, tiles, MDF and ceramic. Not for polyethylene, polypropylene, mirrors or permanent water immersion.

Selleys Liquid Nails is the original high-strength construction adhesive — a solvent-based, all-weather bonder for tough interior and exterior building jobs. This 320g pack delivers a proven, long-lasting hold across the widest range of building materials.

Key Features

• Solvent-based, high-strength construction adhesive
• Excellent water resistance
• Suitable for interior and exterior use
• Meets Australian Standard AS 2329-1999
• Paintable once fully cured
• Made in Australia

Ideal for: Bonding timber, panelling, skirting and architraves, plus timber to concrete, tiles, MDF and ceramic. Not for polyethylene, polypropylene, mirrors or permanent water immersion.

Selleys Liquid Nails is the original high-strength construction adhesive — a solvent-based, all-weather bonder for tough interior and exterior building jobs. This 320g pack delivers a proven, long-lasting hold across the widest range of building materials. Supplied as a trade 20-pack of the 320g cartridge.

Key Features

• Solvent-based, high-strength construction adhesive
• Excellent water resistance
• Suitable for interior and exterior use
• Meets Australian Standard AS 2329-1999
• Paintable once fully cured
• Made in Australia

Ideal for: Bonding timber, panelling, skirting and architraves, plus timber to concrete, tiles, MDF and ceramic. Not for polyethylene, polypropylene, mirrors or permanent water immersion.