Epoxy & General Glues

Windshield Saver is a UV-cure kit for repairing chips and small damage in a windscreen, up to 3.1 cm across.

Key features

• UV-cure resin system.
• Helps stop the damage spreading.
• Reduces the look of the chip.

Where to use

• Windscreen damage up to 3.1 cm in diameter.

Specifications

MarineWeld is a two-part epoxy for boats and other marine equipment. This twin-tube pack is 57 g. It has a paste consistency for filling gaps, and once cured it can be sanded, drilled, tapped, shaped and painted.

Key features

• Tensile strength 5020 PSI.
• Sets in 4–6 hours. Full cure in 16–24 hours.
• Cures grey.
• Waterproof, with a high bond strength.
• For repairs on boats, pools, plumbing and other marine equipment.

Suitable surfaces

• Best on aluminium, other metals and fibreglass.
• Also bonds rigid plastic and wood.

Specifications

Surface preparation

Clean the repair area with detergent or a degreaser, then roughen it with a file or coarse sandpaper. Mix equal parts and apply.

Documents

• Safety data sheet

J-B Weld Original Cold Weld is a steel-reinforced two-part epoxy for high-strength bonding and gap filling. The carded pack holds two tubes (28.4 g each). Mix equal parts, then apply. After it cures to a dark grey, the bond can be shaped, tapped, filed, sanded, drilled and painted.

Key features

• Strongest epoxy in the J-B Weld range. Published tensile strength is 5020 PSI.
• Paste consistency for filling gaps and cracks, as well as bonding parts.
• 1:1 mix ratio. Sets in 4–6 hours at room temperature. Full cure in 15–24 hours.
• Heat resistance to 287°C (550°F) once fully cured.
• Fuel resistant.
• Suited to high-strength repairs and craft work on metal and other hard surfaces.

Suitable surfaces

• Best on metal, stone, concrete and fibreglass.
• Also bonds rigid plastic, wood and ceramic.
• Not for polypropylene or polyethylene.

Specifications

Surface preparation

Clean the repair area with detergent or a degreaser, then roughen it with a file or coarse sandpaper. Dispense equal amounts from each tube, mix until the colour is even, and apply.

Documents

• Safety data sheet 1
• Safety data sheet 2

Selleys Araldite Super Strong is a two-part (resin and hardener) epoxy adhesive that delivers an exceptionally strong, load-bearing bond for heavy-duty repairs. This 35ml pack mixes in equal parts and cures to a rigid, gap-filling bond that dries clear.

Key Features

• High-strength epoxy that holds up to 150kg once fully cured
• Dries clear for a clean, discreet finish
• Excellent chemical and heat resistance
• Highly water resistant once cured
• Rigid, gap-filling bond ideal for tough repairs
• Long working time for accurate positioning of parts

Ideal for: Bonding metal, glass, wood, ceramics, china, crystal, leather, fabric and rigid plastics. Not suitable for polyethylene, polypropylene or flexible materials.

Selleys Araldite Super Strong is a two-part (resin and hardener) epoxy adhesive that delivers an exceptionally strong, load-bearing bond for heavy-duty repairs. This 24ml pack mixes in equal parts and cures to a rigid, gap-filling bond that dries clear.

Key Features

• High-strength epoxy that holds up to 150kg once fully cured
• Dries clear for a clean, discreet finish
• Excellent chemical and heat resistance
• Highly water resistant once cured
• Rigid, gap-filling bond ideal for tough repairs
• Long working time for accurate positioning of parts

Ideal for: Bonding metal, glass, wood, ceramics, china, crystal, leather, fabric and rigid plastics. Not suitable for polyethylene, polypropylene or flexible materials.

Selleys Araldite Super Strong is a two-part (resin and hardener) epoxy adhesive that delivers an exceptionally strong, load-bearing bond for heavy-duty repairs. This 8ml pack mixes in equal parts and cures to a rigid, gap-filling bond that dries clear.

Key Features

• High-strength epoxy that holds up to 150kg once fully cured
• Dries clear for a clean, discreet finish
• Excellent chemical and heat resistance
• Highly water resistant once cured
• Rigid, gap-filling bond ideal for tough repairs
• Long working time for accurate positioning of parts

Ideal for: Bonding metal, glass, wood, ceramics, china, crystal, leather, fabric and rigid plastics. Not suitable for polyethylene, polypropylene or flexible materials.