Anchors

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M10
• Overall length: 130mm
• Recommended drill hole: 12mm
• Recommended drill depth: 90mm
• Max fixture thickness: 25mm
• Effective (embedment) length: 115mm
• Finish: Hot-dip Galvanised (outdoor)

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M10
• Overall length: 130mm
• Recommended drill hole: 12mm
• Recommended drill depth: 90mm
• Max fixture thickness: 25mm
• Effective (embedment) length: 115mm
• Finish: Zinc Plated (indoor)

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M12
• Overall length: 160mm
• Recommended drill hole: 14mm
• Recommended drill depth: 110mm
• Max fixture thickness: 30mm
• Effective (embedment) length: 140mm
• Finish: Hot-dip Galvanised (outdoor)

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M12
• Overall length: 160mm
• Recommended drill hole: 14mm
• Recommended drill depth: 110mm
• Max fixture thickness: 30mm
• Effective (embedment) length: 140mm
• Finish: Zinc Plated (indoor)

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M8
• Overall length: 110mm
• Recommended drill hole: 10mm
• Recommended drill depth: 80mm
• Max fixture thickness: 15mm
• Effective (embedment) length: 95mm
• Finish: Zinc Plated (indoor)

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M8
• Overall length: 110mm
• Recommended drill hole: 10mm
• Recommended drill depth: 80mm
• Max fixture thickness: 15mm
• Effective (embedment) length: 95mm
• Finish: Zinc Plated (indoor)

ChemSet 101 PLUS is a multi-purpose, marine-grade polyester adhesive for anchoring threaded studs and starter bars in solid and hollow substrates. It delivers full load capacity even in flooded holes (EAD-330499 Option 7), is styrene-free and VOC compliant.

• Fast cure – approx. 50 minutes @ 20°C
• Non-drip formulation, suitable for overhead work
• Vibration resistant once cured
• Marine-grade resin for wet/flooded hole performance

Specifications

• Cartridge size: 380ml
• Pack quantity: 16/pack
• Density: 1.69 kg/litre @ 20°C

ChemSet 101 PLUS is a multi-purpose, marine-grade polyester adhesive for anchoring threaded studs and starter bars in solid and hollow substrates. It delivers full load capacity even in flooded holes (EAD-330499 Option 7), is styrene-free and VOC compliant.

• Fast cure – approx. 50 minutes @ 20°C
• Non-drip formulation, suitable for overhead work
• Vibration resistant once cured
• Marine-grade resin for wet/flooded hole performance

Specifications

• Cartridge size: 600ml
• Pack quantity: 12/pack
• Density: 1.69 kg/litre @ 20°C

A complete starter kit for the ChemSet 101 PLUS chemical anchoring system, built around the same marine-grade polyester adhesive used across the 101 PLUS range.

• Includes 2 x 380ml ChemSet 101 PLUS cartridges plus mixing nozzles
• Convenient one-purchase kit for small anchoring jobs

Specifications

• Pack configuration: 2 x 380ml cartridges
• Adhesive type: Polyester

ChemSet 801 XTREM XC² is a fast-setting, heavy-duty vinyl ester adhesive. Its premium high-strength formulation is certified for seismic and flooded conditions and is fire rated.

• Meets the highest seismic performance standards (C1 & C2 certified)
• Suited to fast-assembly structural applications – steel, handrails, balustrades
• 100-year working life claim

Specifications

• Cartridge size: 380ml
• Pack quantity: 12/pack

ChemSet 801 XTREM XC² is a fast-setting, heavy-duty vinyl ester adhesive. Its premium high-strength formulation is certified for seismic and flooded conditions and is fire rated.

• Meets the highest seismic performance standards (C1 & C2 certified)
• Suited to fast-assembly structural applications – steel, handrails, balustrades
• 100-year working life claim

Specifications

• Cartridge size: 600ml
• Pack quantity: 16/pack

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M10
• Overall length: 130mm
• Recommended drill hole: 12mm
• Recommended drill depth: 90mm
• Max fixture thickness: 25mm
• Effective (embedment) length: 115mm
• Finish: Zinc Plated (indoor)
• Pack quantity: 10

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M12
• Overall length: 160mm
• Recommended drill hole: 14mm
• Recommended drill depth: 110mm
• Max fixture thickness: 30mm
• Effective (embedment) length: 140mm
• Finish: Zinc Plated (indoor)
• Pack quantity: 10

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M16
• Overall length: 190mm
• Recommended drill hole: 18mm
• Recommended drill depth: 125mm
• Max fixture thickness: 40mm
• Effective (embedment) length: 165mm
• Finish: Zinc Plated (indoor)
• Pack quantity: 10

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M8
• Overall length: 110mm
• Recommended drill hole: 10mm
• Recommended drill depth: 80mm
• Max fixture thickness: 15mm
• Effective (embedment) length: 95mm
• Finish: Zinc Plated (indoor)
• Pack quantity: 10

The Ramset ChemSet Maxima Spin Capsule is a heavy-duty, acrylic capsule anchor with a measured adhesive dose to suit Ramset ChemSet Anchor Studs. ETA certified for fast loading in dry, wet and flooded holes.

• One capsule per hole – no mixing, no mess, no waste
• Ideal for small jobs with few fixings
• Well suited to overhead anchoring

Specifications

• Thread size: M10
• Cure time: approx. 20 minutes @ 20°C
• Service temperature range: -23°C to 60°C
• Substrates: solid concrete, stone, brick

The Ramset ChemSet Maxima Spin Capsule is a heavy-duty, acrylic capsule anchor with a measured adhesive dose to suit Ramset ChemSet Anchor Studs. ETA certified for fast loading in dry, wet and flooded holes.

• One capsule per hole – no mixing, no mess, no waste
• Ideal for small jobs with few fixings
• Well suited to overhead anchoring

Specifications

• Thread size: M16
• Cure time: approx. 20 minutes @ 20°C
• Service temperature range: -23°C to 60°C
• Substrates: solid concrete, stone, brick

HiFlo mixing nozzles for fast, consistent dispensing of Ramset's Pure Epoxy, Epoxy Acrylate and Vinyl Ester chemical anchoring adhesives.

• Always use the nozzle recommended for the specific adhesive – the wrong nozzle causes improper mixing and reduced load resistance

Specifications

• Pack quantity: 5
• Minimum hole diameter: 10mm
• Maximum hole depth: 240mm (425mm with extension)

Cleaning dust and debris from drilled holes is essential to achieve full adhesion and rated load capacity from chemical anchors. This high-volume pump is part of Ramset's hole-cleaning accessory range.

• Removes dust to help achieve rated load capacities
• Part of the full Ramset chemical-anchoring accessories range

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M10
• Overall length: 130mm
• Recommended drill hole: 12mm
• Recommended drill depth: 90mm
• Max fixture thickness: 25mm
• Effective (embedment) length: 115mm
• Finish: Hot-dip Galvanised (outdoor)
• Pack quantity: 10

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M12
• Overall length: 160mm
• Recommended drill hole: 14mm
• Recommended drill depth: 110mm
• Max fixture thickness: 30mm
• Effective (embedment) length: 140mm
• Finish: Hot-dip Galvanised (outdoor)
• Pack quantity: 10

ChemSet Anchor Studs are engineered from quality Grade 5.8 carbon steel to get the most out of adhesive tensile capacities and provide higher shear capacities than regular Grade 4.6 grade studs. Zinc-plated for indoor/dry-climate use, hot-dip galvanised to Australian Standards for outdoor use, or available in AISI 316 (A4) stainless steel for high-corrosion, coastal environments.

• High performance Grade 5.8 carbon steel for higher tensile/shear capacity than standard Grade 4.6 studs
• Pre-cut to standard chemical-anchoring lengths with a depth-set mark for correct embedment
• External hex drive for reliable capsule/adhesive installation
• Chisel-ended to prevent unthreading

Specifications

• Thread size: M16
• Overall length: 190mm
• Recommended drill hole: 18mm
• Recommended drill depth: 125mm
• Max fixture thickness: 40mm
• Effective (embedment) length: 165mm
• Finish: Hot-dip Galvanised (outdoor)
• Pack quantity: 10

The ChemSet Universal Applicator from Ramset dispenses every product in the ChemSet Injection adhesive range.

• Fits all Ramset chemical injection adhesive cartridges
• Metal construction
• Twin drive mechanism

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 49mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 55mm
• Max fixture thickness: 20mm
• Effective length: 42mm
• Fixture hole: 12mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M6
• Anchor length: 34mm
• Drilled hole diameter: 6mm
• Minimum hole depth: 40mm
• Max fixture thickness: 10mm
• Effective length: 30mm
• Fixture hole: 8mm
• Finish: Zinc plated, countersunk/flat head

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 103mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 80mm
• Max fixture thickness: 50mm
• Effective length: 96mm
• Fixture hole: 12mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 124mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 85mm
• Max fixture thickness: 80mm
• Effective length: 117mm
• Fixture hole: 12mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 41mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 50mm
• Max fixture thickness: 3mm
• Effective length: 34mm
• Fixture hole: 12mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 76mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 65mm
• Max fixture thickness: 30mm
• Effective length: 69mm
• Fixture hole: 12mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M12
• Anchor length: 55mm
• Drilled hole diameter: 12mm
• Minimum hole depth: 70mm
• Max fixture thickness: 10mm
• Effective length: 47mm
• Fixture hole: 15mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M12
• Anchor length: 70mm
• Drilled hole diameter: 12mm
• Minimum hole depth: 70mm
• Max fixture thickness: 15mm
• Effective length: 62mm
• Fixture hole: 15mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M20
• Anchor length: 113mm
• Drilled hole diameter: 20mm
• Minimum hole depth: 125mm
• Max fixture thickness: 25mm
• Effective length: 102mm
• Fixture hole: 24mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M20
• Anchor length: 157mm
• Drilled hole diameter: 20mm
• Minimum hole depth: 155mm
• Max fixture thickness: 70mm
• Effective length: 146mm
• Fixture hole: 24mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M20
• Anchor length: 81mm
• Drilled hole diameter: 20mm
• Minimum hole depth: 100mm
• Max fixture thickness: 8mm
• Effective length: 70mm
• Fixture hole: 24mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M6
• Anchor length: 57mm
• Drilled hole diameter: 6mm
• Minimum hole depth: 55mm
• Max fixture thickness: 30mm
• Effective length: 53mm
• Fixture hole: 8mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M8
• Anchor length: 40mm
• Drilled hole diameter: 8mm
• Minimum hole depth: 50mm
• Max fixture thickness: 6mm
• Effective length: 34mm
• Fixture hole: 10mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M8
• Anchor length: 60mm
• Drilled hole diameter: 8mm
• Minimum hole depth: 70mm
• Max fixture thickness: 20mm
• Effective length: 30mm
• Fixture hole: 10mm
• Finish: Zinc plated, countersunk/flat head

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M8
• Anchor length: 66mm
• Drilled hole diameter: 8mm
• Minimum hole depth: 65mm
• Max fixture thickness: 25mm
• Effective length: 60mm
• Fixture hole: 10mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M8
• Anchor length: 85mm
• Drilled hole diameter: 8mm
• Minimum hole depth: 75mm
• Max fixture thickness: 45mm
• Effective length: 30mm
• Fixture hole: 10mm
• Finish: Zinc plated, countersunk/flat head

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M8
• Anchor length: 92mm
• Drilled hole diameter: 8mm
• Minimum hole depth: 75mm
• Max fixture thickness: 50mm
• Effective length: 86mm
• Fixture hole: 10mm
• Finish: Zinc plated, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 103mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 80mm
• Max fixture thickness: 50mm
• Effective length: 96mm
• Fixture hole: 12mm
• Finish: Hot-dip galvanised, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 41mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 50mm
• Max fixture thickness: 3mm
• Effective length: 34mm
• Fixture hole: 12mm
• Finish: Hot-dip galvanised, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 49mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 55mm
• Max fixture thickness: 20mm
• Effective length: 42mm
• Fixture hole: 12mm
• Finish: Hot-dip galvanised, hex nut

The DynaBolt Plus Sleeve Anchor is a medium-duty, torque-controlled expansion anchor with an integrated pull-down section, designed for anchoring timber and steel fixtures to concrete, brick or block. It is available in a variety of head styles and finishes.

• Patented expansion sleeve closes gaps of up to 5mm, pulling down on the fixture to induce clamp load
• Fully assembled through-fixture anchor – no separate parts to lose on site
• Eliminates assembly, marking-out and re-positioning steps for fast, easy installation
• Multiple head styles (hex nut, hex bolt, countersunk/flat, round) suit a wide range of applications

Specifications

• Anchor size: M10
• Anchor length: 76mm
• Drilled hole diameter: 10mm
• Minimum hole depth: 65mm
• Max fixture thickness: 30mm
• Effective length: 69mm
• Fixture hole: 12mm
• Finish: Hot-dip galvanised, hex nut